With the increase of air as well as ground air pollution as well as the wrongs of toxic wastes being unloaded in our reservoirs and other water sources, it needs to be no surprise to you that our drinking water is continuously in danger of being contaminated. Whole residence water filters are an all-in-one sensible option for eliminating harmful bacteria and detoxifying your water.
What is an entire house water filter?
Equally, as its name suggests an entire home water filter is used to detoxify the water for your whole home. This sort of water filter is linked to the main water line in your house for that reason dispensing clean water throughout your home. This includes showers, toilets, water faucets, cooking area, as well as bathrooms.
Figuring out the type of entire residence water filter system you will certainly need will certainly depend only on the kind of contaminants found in your water system.
The expense of acquiring a home water filtering system can be rather costly if you’re on a tight budget. However compared to acquiring several solitary water filters for every single faucet in your home, a whole residence water filter system is a lot more sensible less costly remedy with time. They ought to additionally be transformed occasionally to provide maximum security.
Exactly how usually should you alter your filter?
Makers suggest transforming water filters every 2 to 6 months, however with that being claimed you ought to replace them whenever you see a decrease in performance. This could be shed water pressure, an unusual preference, or a decline in the flow rate. Water filters utilized in the whole house or turn around osmosis systems need to be transformed every 2 months or 8,000 gallons of water.
Exactly how usually you need to change your water filter depends upon how much water you and your family usage on a daily basis. If you have a huge family that takes in several gallons of water, as well as cleans huge baskets of garments once a week as well as takes normal showers daily after that you checking out replacing your filters extremely often.
What kinds of typical water contaminants you should look for?
Sediments– are recognized to be also visible fragments in the water which need to be mechanically strained out, this would include sand, dust, corrosion, and also dust. Water materials that nurture a substantial quantity of debris need to be executed in several phases of sediment filtering.
Iron– ferrous (aka liquified or clear water iron) and ferric (also known as rust or red water iron) are both kinds of iron that are normally found in water materials. Clearwater iron can be gotten rid of with ion or oxidation exchange. Sediment filters are capable of removing rust bits, and also red water iron.
Chemicals– Chlorine is the most usual chemical anti-bacterial found in community water materials as well as can be eliminated with a carbon water filter.
Two primary types of entire residence water filter systems:
# 1. Sturdy filtering system
This impurity elimination system carries out at the highest level because of the WholeHouseFilterfact that it makes use of huge amounts of filter media. The media is placed in a tank that stands concerning 2 feet 10 ″ tall as well as supplies iron security for 5-10 years its substitute routine. The small single storage tank system attaches to the primary water supply line of your house.
# 2. Common capability water cartridge
These water filter cartridges are positioned inside long-lasting filter real estates to treat the polluted water throughout the whole house. The filters are typically 4.5″ D by 10″ or 20″ H as well as are put at the main water line. These ability systems are affordable and also typical, nevertheless, they do call for more upkeep due to the fact that these filters should be changed out often.
Look for budget-friendly entire house water filter systems if you desire the ideal as well as highest possible carrying out pollutant elimination system look for sturdy filtering systems and also for common ability filtering.
Simply as its name recommends an entire house water filter is made use of to purify the water for your entire home. Compared to acquiring several single water filters for every tap in the residence, an entire home water filter system is the much more sensible less costly remedy over time. Water filters made use of in the entire home or reverse osmosis systems ought to be changed every two months or 8,000 gallons of water.
Iron– ferrous (also known as dissolved or clear water iron) and also ferric (also known as rust or red water iron) are the 2 kinds of iron that are generally found in water products. These water filter cartridges are placed inside resilient filter real estates to deal with the polluted water throughout the whole home.
Finest Tap Water Filters – Buyer’s Guide
1. Budget as well as the right price
Make a listing of what you want in your Water Cleanser as well as how much you’re willing to spend on it. So try to find an item within that cost range and also pick the one that interests you the most. One tip we want to give you is this: don’t search for a less costly item if it does not even have the performance you require.
2. Does it have all the features you need?
Most notably, the Water filter you are acquiring needs to have all the functions you are trying to find. In case you do not even have one, don’t buy it! Since you won’t be able to utilize it for that objective, we are saying this.
Purchasing your Faucet Water Filter from a trustworthy brand name can truly make good sense. Not just is it better than others in “construct quality”, however it additionally has some additional functions as well as far better client assistance. Famous brand names have lots of solution facilities nationwide, so if there is any problem, you can merely bring your Water Filter to among their service centers.
4. Service warranty problems!
When you acquire the Tap Water Filter from a widely known brand name, you obtain a warranty. That’s why I always recommend acquiring items from trustworthy brands and also required products.
In a society increasingly sensitive to eco-friendly sustainability concerns, the suggestion of decreasing plastic consumption is remarkable to everybody. Even more so if you think about not having to go to the grocery store to fill up water tanks that in the blink of an eye you’ll have to buy again. These are just 2 of the reasons that many people reveal a rate of interest in the residence water cleanser and also make a decision to go in the direction of an extra lasting lifestyle, they choose to buy one and enter the increasingly vibrant market. as well as variety. provides people the chance to fulfill their demands and go one action even more towards an eco-friendly and also healthy and balanced way of life.
Most significantly, the Water filter you are getting should have all the attributes you are looking for. Acquiring your Faucet Water Filter from a reliable brand can really make feeling. Famous brand names have numerous service centers nationwide, so if there is any problem, you can merely bring your Water Filter to one of their solutions.
When you get the Tap Water Filter from a widely known brand, you get a warranty. These are simply two of the reasons why numerous people show interest in the residence water purifier and also make a decision to go in the direction of a much more lasting way of life, they pick to get one and also go into the progressively vibrant market.
Be it drills, screwdrivers, saws, or grinders – power tools make life easier for not only your professionals but also hobbyists.
Despite having a well-prepared job, the drill can go astray when drilling into the wall surface. Consequently, the pinhole is as well big and distorted.
We provide some choices on just how you can repair and fill up drill openings.
Numerous DIYers recognize the issue with exploration and also reduction: the marks are positioned and also lined up, the initial holes are made and after that, with the last hole pierced, things are unexpectedly completely different.
Quickly, the drill bit vanished into the wall, the machine damaged apart, and also the drill dust was up to the flooring.
Congratulations! You currently have a drill opening two times as big as planned. And it was absolutely wrong
Just how can I repair the drill opening currently?
We will reveal it to you!
Even if the outcomes are constantly the same, there are many reasons that the hole is so large: Most of the moment you have actually just touched the side of a rock in a plastered brick wall.
The drill after that complies with the course with the least resistance and lacks the joint.
An additional possibility: You have actually machined a vacant block with your hammer drill or hammer crusher. Outcome: collapsing! Other predefined fault factors: old sub-point, wet wall, cord duct.
Four alternatives: Deal with the hole
Put larger, ideal pin. Forecast: negative! The screws seldom fit now. The look is gone and also usually, no huge pin will hold in a screwed opening.
Repeat drill inconsistency. Diagnosis: May work, however, will your openings still fit the rack? And: must load the old hole!
Fill the hole, drill back in place. Overview: If you have time to wait on your leveling compound to set – and afterward not encounter the same issue due to cracks in the wall surface – a sensible choice.
Make use of the existing hole and keep the given lock in a huge hole. Projection: A suitable remedy! Just how to do that as well as what products you require, see below!
Repair boreholes without pins
This sensible assistant completely replaces the fix (nylon): Fischer “fill as well as repair” is a solvent-free two-component mass based upon polyurethane.
It is blended automatically when it is squeezed out of the syringe. Practical “filling up & repair work” fits all developing materials, even wood. A wood screw just screwed to the block promptly hardens.
Drill opening filling: Repair with filler
A famous item, the well-known method of working: With the repair work barrier, you can return the latch immediately without much stirring!
That’s how it’s done:
. Fill up the drill hole with filler
. Press the latch
. Get rid of sticking out fillers
. Eliminate the sculpt overhang
The setup time is about 2 hours, the masonry needs to not be fined sand or dusted. The tube can still be made use of
Have your physician fix the hole with plaster tape
If these tampons noise acquainted, opportunities are you’ve had a broken arm or leg at some point. There is plaster of plaster in the fish farmer, plasterer, or clinical item.
Plaster tape only has to be neatly reduced. Soaking as well as handling times are according to the supplier’s directions. Cut to size, wrap the pin a few times, moisten, insert, done
It is clear that painting requires a professional to produce excellent results. All over the world, people love to approach expert paint sprayers to remain competitive in their area of interest.
There are numerous varieties of colors available to the clients in the modern-day that make the task that any amateur can accomplish. Before commencing your furniture painting work, it is imperative to comprehend the item to use, the creativity you will apply and, of course, the surface of paint precisely.
An influential Sales and Marketing Director of a company based in Minneapolis Steve Engleson said that selecting the best sprayer is knowing when and how the tool will be used.
Selecting the paint sprayer
Since you are dealing with furniture, it is recommended to understand that the viscosity of the liquid determines the tip of the sprayer you use.
There are different spray tips that come with various holes sizes ranging from 0.011 to 0.21 inches. Most useful tip sizes for furniture painting range from 0.011 to .015 inches.
Don’t forget that if you plan to increase the tip of the sprayer to fit your preference, this will proportionally be determined by the liquid viscosity. Most paint sprayer amateurs and professionals make grave mistakes when they tend to focus so much on the horsepower rather than the tip size the sprayer can hold.
Stock up all the supplies you need
To ensure you produce a professional look at your painting, collect all the tools you need to avoid unnecessary interruptions back to the store so as to maintain your concentration.
Glen O. Gabbard, a high-ranking psychology authors in the 18th century, quoted that, ‘human mind depends on the power to focus on excellent results.’ Some of the necessary tools, you will require include;
Don’t fall into the ensnare of purchasing contemptible or generic paint brands; go for known brands like Rust-Oleum or Krylon despite the fact that they are quite expensive. Unlike when dealing with house walls, furniture spray painting has various finishing preferences. There is flat to the high gloss of which the high gloss is friendly to clean.
Spotless your furniture
Scrape off all the loose pieces or cracks on your furniture. Sometimes you will have to take time and tighten loose screws to make your furniture sturdy. Remember to sand the piece repeatedly and pay special attention to rough areas. If you’re dealing with wood furniture, consider sanding it in the direction of the grain to avoid making the rough again. Once you are done with sanding, take a damp cloth and wipe all the dust available on your furniture.
Ventilate your place
The paint sprayer has tip holes that squeeze the liquid to vapor form. If you do your painting in a poorly ventilated room, then you are likely to inhale the paint which is very poisonous.
Whether in a ventilated room or not, always remember to put on your mask. Avoid entirely painting in windy days because the paint can be blown away or drop in your wet project. Cover areas that you are not painting to ensure that your finish is splendid and not flabby.
Some of the professionals advise people to use close strokes in order to have your paint intact. However, as an expert in this field, I recommend my clients to use long, even strokes. This is primarily because when you use short, uneven strokes one might end up getting rings or built-up paint marks. Drips are very familiar with amateurs but if you want to appear professional, concentrate on the furniture joints, corners, legs, or ornate details to deal with dripping correctly. Statistics has depicted that many people prefer to paint sprayer because it takes less than ten minutes to dry up as compared to ordinary painting methods.
Everyone is naturally attracted to beautiful and healthy stuff. Can you imagine your colleagues swearing that your house is cute, but your furniture is dull? The obvious answer is no.
Therefore, after spray painting your piece, please use a seal. It appears even magnificent if the piece is high-use furniture like the dining table. An excellent coat like of poly-acrylic will increase the beauty longevity of your furniture. Do not feel hurt in any way, remember beauty is a choice.
Don’t panic if you make a mistake
Painting is a tiresome job especially if you are painting many furniture. Others once they complete the painting jobs, require total rest like nothing else. Some once they make painting mistakes they panic and desire to quit the entire project. In case you commit a mistake, don’t worry. Just sand it though it might take longer it’s worth. If you realize that the paint does not stick, apply priming to solve the issue of dripping.
Now once you are done, take time for the paint to dry and enjoy your beautiful experience with a paint sprayer.
If you feel you don’t like your piece, remember there is nothing else that can make your furniture appear attractive than a paint sprayer. It is true that paint sprayer is a multi-purpose painting too. However, if you want to astonish even the most sprayer painting professionals, adhere to the above guidelines.
Air compressors are the most common ones we can find both indoors and in professional environments; Its uses are limitless and anyone can find help with their activities:
inflatable tires for bicycle, motorbike, automobile, water game, air blowing to clean tools, working environment, as well as connecting electric tools to unscrew and screw nuts, nail shot, paint, chisel, sand and more.
Exactly how to pick a 60-gallon air compressor
1. Use compressor for high-pressure heavy applications
The first difference is between home and industrial use: first of all, the amount of pressure and volume of air required by the application range.
If you’re planning on powering a heavy machine, you obviously need more pressure and volume. The use of a compressor that is smaller and less efficient is due to planned use.
On the one hand is work inefficiency, which is determined by waiting time to refill the tank
On the other hand, it puts you in danger of exposing the air compressor components to excessive wear, forcing you to work at their power limits.
2. A suitable electrical system?
When choosing the right compressor, it’s important to consider the type of power supply you have available. If your work environment requires a lot of currents, you can have a three-phase system,
Usually, however, you have a single-phase system so it’s best to check it out, as this data makes a difference in the choice of a compressor.
Single-phase systems can power motors up to 3 HP. On the other hand, a three-phase system allows you to power a compressor with a higher capacity, as long as the amperage is sufficient.
3. Where to use the compressor? Do you need a silent compressor?
The noise level of your compressor is closely related to your working environment. Of course, it also depends on the size of the compressor: the larger the exhaust volume, the more noisy the compressor tends to be.
The silent compressor model fits your needs if you prioritize minimizing the noise generated while the machine is operating. If you choose a piston compressor and you want to store it out, equip a suitable carrying case to protect it from atmospheric agents and keep it well-ventilated at all times.
Also, ensure that there is enough space around the machine for easy use of the machine and comfortable maintenance operations. Do you work in a home environment and want to minimize the noise?
Choose our silent compressor! The ideal replacement for those looking for a powerful yet quiet compressor is a screw compressor. Also known as camcorders, these compressors are quieter, as they exploit a different technology from the piston and have the parts wrapped in a special cabinet.
The advantage of using screw air compressors lies in its quiet operation and higher quality air generation as it is virtually impulsive.
If you need a larger volume of compressed air, this is the right type of compressor. Among the most frequent applications of screw compressors are spray paint on large surfaces, as is the case in the case of car bodies in large automobile workshops.
4. Is air quality important when choosing your air compressor?
The answer is yes! The compressor sucks in ambient air. Everyone knows that water and oil must be clean for machines to function properly. The same goes for the air used by your compressor.
Dirt causes problems: low quality compressed air can damage your machine and negatively affect your work. On the other hand, the air quality is better, helping you to reduce problems and maintenance.
Oil-water separators and dryers assist you when it comes to achieving the air quality you want for your compressed air system. These constitute an additional cost, as well as an increase in energy expenditure, but greatly reduce the risk of your compressor failure, as well as inaccuracies and inconveniences at work, help your equipment. you are more durable and reliable.
5. How to choose compressor size
How much air do you need?
The size of the system is also important and depends entirely on the type of pneumatic tool you connect to your compressor. If you are unsure which size to choose, please contact your nearest distributor.
6. Which pneumatically-driven device to make use of with my air compressor?
The amount of air you require is determined by the devices that make use of that air. It might seem obvious, but it’s easy to neglect this factor. Trai recommended from our p.
Just how commonly do you use your pneumatically-driven tools? Drills, medical suction makers, pneumatically-driven screwdrivers, and pneumatic ratchets wrench are the main tools used for interruptions.
If you use and blowers and also sand blowers you’ll need much more pressed air as well as will likely rely upon three-phase compressors (industrial source of power) to run them.
Another suggestion: when you are evaluating the size of the compressor to run your pneumatic tools, bear in mind the data representing the free airflow (FAD), i.e. the air provided, no. the gas has to be sucked.
Have you ultimately discovered the best compressor for you?
You can not undervalue the benefits of having an excellent compressor in your store, but you most definitely have to think about a lot of different factors. After reading this article you should have a better understanding of 60-gallon compressors so you can make the appropriate choice.
Getting a 60-gallon compressor is a huge financial investment, yet it can also make you do your job a lot more efficiently.
Buy the right kitchen: everything you should consider
Do you want to buy a kitchen or are you planning a new kitchen? Or you just need a new oven
On this page, I show you the most popular oven combinations. Here are some tips on what to look for when buying induction cookers.
I have summarized all the important criteria such as air circulation, energy layer, volume, or induction in a table for you.
I also divide them into categories such as gas stoves or electric stoves. You can also choose from an integrated or free standing kitchen.
Factors to Consider Before Buying an Induction Cooktop
Cooking: A daily ceremony
It’s no wonder that the kitchen in a house becomes the center of life and is the pride of many housewives and now also housewives.
Cooking is not only easy to prepare food but a daily ceremony and challenge one of the great foods to create.
Of course, there are also people whose diet is of secondary importance and mostly limited to fast food and microwaves. The trouble starts with buying the kitchen.
A stove is used today as a cooking tool and if the tool is also high quality, it will be easier and easier to work with.
With this article on stoves and ovens, I want to help you find the stove that best suits you.
When buying a kitchen, there are many things to look for that seem insignificant at first glance, but it’s effective for everyday use.
Gas cookers, electric cookers, or induction cookers are basic questions. On my page about buying kitchens, I will do some comparisons. In the end, everyone can decide which kitchen is best for them!
4 tips before buying the kitchen from
1.From setting counters to pans: everything you need to know before evaluating a kitchen purchase.
The choice of a new cooking plate is not solely determined by a purely aesthetic factor.
It is essential to bear in mind some aspects that may prove to be a problem.
These useful design objects hide small pitfalls, great to know to enjoy their performance.
One of the most frequently asked questions regarding electricity consumption. With touch preferences, you’re conscious of buying a product that runs on electricity rather than gas, like the classic stove we are used to.
However, increasing the power supplied will also require a higher cost in the bill. Anyone who has the capacity, both economically and spatially, can consider the idea of installing an alternative energy generator.
After addressing energy consumption issues, it’s time to move on. Which model could be better suited to your needs? To know this, several factors need to be considered: the design of the kitchen, the size, and the number of people in the home.
As you know, not all cookware is compatible with touch systems. This is due to the fact that, unlike traditional stoves, they are powered by electromagnetic waves.
For this reason, only conductive trains can be used, so in iron, steel, or cast iron, it can be used.
However, to avoid inaccurate or useless purchases, we first recommend checking the battery of the pot you already own: through a simple magnet, go to the bottom of each container.
But don’t worry, some manufacturer brands offer stainless steel models for sale, perfect for touch systems.
If these basics are solved first, you can come up with more detailed plans and technical issues by lighting, of course, the question of some integrated ovens or stoves. Very high free.
Especially with an integrated kitchen, it is important to ensure that the right connections are in place.
Each type of stove has a large selection and model, simpler models, and is somewhat more complex in all price ranges.
Of course, when buying a kitchen, personal financial options also play a role in what is and cannot be purchased.
However, many models are also available without an oven, but if you want the stove to have an oven, don’t overlook the oven.
If you want to win basketball games, your players must be able to finish at the rim consistently.
While knowing “how to do a layup” will sound easy to most players, it’s actually much more difficult than most people realize.
Think about it:
Players attack the hoop at varying speeds…
Players attack the hoop from many different angles…
And when they do get to the hoop, there’s usually a second defender waiting who will attempt to swat their layup into the 5th row.
Despite these challenges, players must learn how to score layups in a variety of situations if they want to experience individual and team success.
In this article, I’ll show you how.
I’ll start by teaching you (1) exactly what a layup is, (2) the six steps for how to do a layup, (3) the process for teaching layups to young kids, (4) the seven layup variations all players must master, before finishing with (5) some important layup tips.
Let’s get started…
What is a Layup?
Here’s the general definition most coaches would use:
“A layup is the action of a player dribbling towards the hoop, taking two steps, and then laying the basketball into the hoop off the backboard.”
For a traditional layup — this is correct.
With that said…
There are MANY variations of a layup (I’ll share 7 of them with you later in this article) and no two in-game layups are identical.
There’s an endless number of situations a player will face when they attack the hoop in a 5-on-5 game.
The two things all layups do have in common:
(1) All layups are shots close to the basket
(2) All layups are worth two points
How to Do a Layup (6-Steps)
Now, let’s talk about how to do a layup correctly.
Learning correct footwork and layup technique is crucial for young players.
We don’t want players to develop poor habits that will be difficult to break out of as they get older and advance to higher levels of basketball.
For the purposes of this beginner’s guide, I’ll assume players are executing a regular right-handed layup.
Here we go:
1. Eyes Up
The very first thing a player must do when they decide to attack the defense and finish with a layup is get their eyes up.
This is important for two main reasons:
a. To Lock onto the Target
The target they aim for will be either the hoop or the backboard depending on the player’s angle and speed.
Knowing which target to choose as the ball is released from the shooter’s hand is something players will get used to as they gain more experience.
b. To Read the Defense
Every time a player attacks the hoop, multiple defenders will step across to provide help and challenge the layup.
Players need to get their eyes up and use their peripheral vision to read these defenders.
This will help the player decide which layup variation will give them the best chance of scoring (or which teammate is now open to receive a pass).
It’s crucial that a player protects the ball while attempting their layup.
Two things to watch out for:
a. Getting Stripped
Smart defenders will look to strip (steal) the ball from the offensive player during their two steps.
To prevent this from happening, the offensive player needs to (1) have strong hands and (2) keep the ball close to their body.
b. Getting Blocked
Tall defenders will attempt to block the shot during the upward shooting motion or as the ball leaves the offensive player’s hands.
To prevent this, the offensive players must use their non-shooting hands to protect the ball and increase the likelihood of getting fouled.
5. Follow Through
The fifth step when learning how to do a layup…
Teach your players to bring the ball up above their head, extend their arm, and then flick their wrist to guide the basketball into the hoop.
The traditional overhand layup is very similar to a regular jump shot when it comes to this part of the layup technique.
If you’re coaching very young players, you might find they push the basketball up from their chest instead of bringing the ball above their head before shooting… this is due to a lack of strength.
This isn’t a big issue while they’re young, but make sure they’re growing out of this habit as they get older and stronger.
Now that your players understand correct layup technique, it’s time they start doing some serious layup practice!
A few important things for coaches to think about:
a. Different Angles and Speeds
Run layup drills that involve players attacking the hoop from different angles and at different speeds.
Left / right side
Front of the rim
Along the baseline
It’s important that they’re comfortable and confident driving to the hoop from anywhere on the court.
b. Right Hand and Left Hand
Allow players to mainly use with their dominant hand when they’re first learning how to perform a layup…
But make sure they start practicing with both hands once they understand correct technique and develop the strength to do so.
This is important to help them protect the ball and finish around good defenders as they get older and play against tougher competition.
Almost immediately you should start running drills where players are required to attack the defense and finish with a layup against live defense.
Add both layup technique and layup competition drills to every practice.
Spend 10 minutes using a layup technique drill and then spend 10 minutes playing half court 2-on-1.
Your players might struggle against competition at first — they might commit a travelling violation, jump off the wrong foot, or rush their two steps — but they’ll benefit from the struggle in the long run.
Teaching Layups to Kids – The Process
I’m guessing that most people reading this article are youth basketball coaches wanting to know the best way to teach layups.
If so, you’re in the right place.
I’m going to provide you with the step-by-step instructions.
These steps should be used to teach “overhand” and “underhand” layups to all players who have signed up to learn the game of basketball.
One final piece of advice before we get started:
These steps might seem simple to you… but to a young kid who’s trying to understand footwork, ball pickup, where to focus, distance, etc… it’s hard!
Let’s get stated…
1. One-Step Layup
The first step is to start players on the low block.
Since most players are right-handed, I recommend starting on the right block since this will be most comfortable for them.
Give everyone a basketball, line everyone up behind the low block, and then get them to execute the following:
a. Start with feet together
b. Take one step with their left foot (inside foot)
c. Jump off the left foot and shoot a layup off the backboard
2. Two-Step Layup
Next, let’s add a second step…
Get everyone to start one step back from the low block.
Reminding them that they don’t need to dribble the basketball yet, ask them to do the following:
a. Start with feet together
b. The first step is with their right foot (outside foot)
c. The second step is with their left foot (inside foot)
d. Jump off the left foot and shoot a layup off the backboard
Players grab their own rebound before joining the end of the same line.
3. One-Dribble Layup
Now let’s take another step back…
For the third step in this process, we ask players to take one dribble before completing their two steps and finishing with a layup.
Here are the instructions:
a. Start with feet together
b. The initial step is with their left foot. As this foot touches the ground, the player should take one dribble with their right hand.
c. As the player catches the ball, they take their first layup step with their right foot (outside foot)
d. The second layup step is with their left foot (inside foot)
e. Jump off the left foot and shoot a layup off the backboard
4. Multiple Dribble Layup
The final step when learning to shoot off the dribble requires players to retreat back behind the three-point arc.
From here, players will before multiple dribbles before gathering the ball, taking their two steps, and laying the ball in off the glass.
Here’s how it works:
a. Start behind the three-point line with a basketball.
b. Take multiple dribbles towards the hoop (eyes up!)
c. At the low block, take the first step with the right foot (outside foot)
d. The second layup step is with their left foot (inside foot)
e. Jump off the left foot and shoot a layup off the backboard
5. Catch and Layup
Another thing players must learn to do is receive the basketball while on the move and then finish with a layup without dribbling.
Players are put in this situation often during games…
They might make an off-ball cut to the hoop, receive a pass from a teammate on a fast break, or pass to a player in the post then cut off them.
My recommendation is to set up a quick “give and go” drill.
a. Put one player on the free-throw line without a basketball.
b. Line everyone else up behind the three-point line with a basketball.
c. The player with the ball passes to the middle of the floor, sprints towards the hoop, and then receives the ball back for a no-dribble layup.
d. Change the “passer” every minute or two.
To help you better understand the whole process, check out this brilliant video from FIBA that shows the first four progressions:
Seven Layup Variations
As I spoke about in the step-by-step section, it’s important for players to master more than one type of layup.
When you’re playing a real 5-on-5 game, there will be help defenders trying to block / alter your shot when you get to the hoop.
Being comfortable with a variety of layups will allow players to finish around any kind of defense that’s thrown at them.
Here’s the must-know list:
1. Overhand Layup
This traditional layup is often the first one we teach young players. It’s similar to a regular jump shot in that a player gets their hand under the ball and “shoots” it off the backboard.
2. Underhand Layup (Finger Roll)
Also known as the “finger roll”. This involves players putting their shooting hand under the ball with their fingers facing forward, and then rolling the ball off their fingertips as they extend their arm to the hoop.
The floater is a great way for smaller players to score inside against bigger defenders. It involves a player “pushing” the ball up over the defense.
4. Off-Foot Layup
If you really want to catch the defense by surprise, an off-foot layup should be in your bag of tricks. This involves jumping off the same foot you’re shooting with. For example, jumping off the right foot for a right-hand layup.
5. Euro Step Layup
The Euro Step involves taking your first step in one direction, and then changing directions for your second step. This is a great way to step around defenders and change the angle as you complete a layup.
6. Reverse Layup
A reverse layup allows the offensive player to attack the hoop and finish on the opposite side of the rim. For players at high levels, the rim acts as protection from shot blockers.
7. Power Layup
A power layup involves performing a 2-foot jump stop before raising up to shoot. The benefit of this variation is it will give the player a stronger base, which is essential if you’re anticipating contact.
Advanced Layup Tips
Before you go, here are a few extra layup tips that will help players be more successful when attacking the hoop.
Some of the tips I’ve mentioned already throughout the article (but they need repeating), and some of them I’ve saved for this section.